Skip to main content

PREVIOUS YEAR QUESTION PAPERS TRIBOLOGY ( KUK )

PREVIOUS YEAR UNSOLVED QUESTION PAPERS – 1 (KURUKSHETRA UNIVERSITY)
TRIBOLOGY
QUE NO. – 1
(A) EXPLAIN TRIBOLOGICAL SYSTEMS AND THEIR CHARACTERISTIC FEATURES. EXPLAIN ONE SYSTEM IN DETAIL?
(B) WHAT ARE THE CAUSES OF FRICTION? STATE AND EXPLAIN ADHESION THEORY OF FRICTION WITH SUITABLE DIAGRAMS?
QUE NO. – 2
(A) WHAT IS TOPOGRAPHY? EXPLAIN IN DETAIL VARIOUS TRIBO – MODELS FOR ASPERITY CONTACTS?
(B) EXPLAIN IN DETAIL THE WORKING OF CROSS – CYLINDER ARRANGEMENT FOR MEASUREMENT OF FRICTION WITH NEAT SKETCHES?
QUE NO – 3
(A) DISCUSS IN DETAIL THE ABRASIVE WEAR. HOW GTHE ABRASIVE WEAR CAN BE PREVENTED? DISCUSS ABRASIVE WEAR RESISTANT MATERIALS?
(B) WRITE SHORT NOTE ON FOLLOWING:
· FRETTING WEAR
· STICK REGIME
· MECHANISM OF WEAR
· CORROSION WEAR
QUE NO. – 4
(A) EXPLAIN RELATIVE IMPORTANCE OF WEAR. WHAT DO YOU MEAN BY SURFACE FATIGUE WEAR?
(B) WHAT ARE THE QUANTITATIVE LAWS OF WEAR? DERIVE THE WEAR EQUATION?
QUE NO.–5
(A) EXPLAIN HYDRODYNAMIC LUBRICATION WITH THE HELP OF NEAT SKETCHES?
(B) EXPLAIN VARIOUS IMPORTANT PROPERTIES OF LUBRICANT?
QUE NO. – 6
(A) EXPLAIN IN DETAILS THE VARIOUS APPLICATIONS OF SLIDING AND ROLLING CONTACT BEARINGS?
(B) WHAT ARE THE DIFFERENT ADDITIVES USED IN LUBRICATING OILS? FOR WHAT PURPOSE THEY ARE ADDED? EXPLAIN
QUE NO. – 7
(A) EXPLAIN HYDROSTATIC BEARING WITH THE HELPM OF NEAT SKETCHES?
(B) EXPLAIN IN DETAIL THE CIRCULAR STEP THRUST BEARING AND WRITE THE PRESSURE DISTRIBUTION EQUATION?
QUE NO. – 8
(A) WHAT ARE THE GENERAL REQUIREMENTS OF BEARING MATERIALS? WHAT DO YOU MEAN BY POROUS BEARINGS?
(B) EXPLAIN THE WORKING OF GAS BEARINGS WITH THE HELP OF NEAT DIAGRAM?


PREVIOUS YEAR UNSOLVED QUESTION PAPERS – 2 (KURUKSHETRA UNIVERSITY)
TRIBOLOGY
QUE NO. – 1
(A) WHAT ARE THE DIFFERENT TECHNIQUES OF SURFACE EXAMINATION? EXPLAIN IN DETAIL
(B) DISCUSS IN DETAIL VARIOUS TRIBO – MODELS FOR ASPERITY CONTACT. WHAT IS TOPOGRAPHY?
QUE NO. – 2
(A) DISCUSS FIVE LAWS OF ROLLING FRICTION. WHAT ARE THE CAUSES OF THE ROLLING FRICTION? HOW THE ROLLING FRICTION IS MEASURED?
(B) WHAT ARE THE TECHNOLOGICAL PROPERTIES OF SURFACES? DISCUSS IN DETAIL
QUE NO. – 3
(A) GIVE VARIOUS TYPES OF WEAR AND EXPLAIN IN DETAIL
(B) HOW THE WEAR IS MEASURED? GIVE WEAR RESISTANCE MATERIALS
QUE NO. – 4
(A) WHAT ARE THE QUANTITATIVE LAWS OF WEAR? DISCUSS ABRASIVE WEAR IN DETAIL
(B) WHAT ARE THE SOURCES AND CAUSES OF WEAR AND EFFECT OF WEAR ON PROPERTIES OF METALS ?
QUE NO. – 5
(A) WHAT IS BOUNDARY LUBRICATION? EXPLAIN WITH THE HELP OF SKETCHES IN DETAILS.
(B) WHAT IS THE FUNCTION OF LUBRICANTS? DISCUSS VARIOUS TYPES OF LUBRICANTS.
QUE NO. – 6
(A) WHAT IS A BEARING? STATE ANY THREE FUNCTION OF BEARING. GIVE APPLICATION OF SLIDING AND ROLLING CONTACT BEARINGS?
(B) WHAT TYPES OF ADDITIVES ARE USED IN LUBRICATING OILS AND WHY? WHAT IS THE EFECT OF LUBRICATION IN I.C. ENGINES?
QUE NO. – 7
(A) DISCUSS AND EXPLAIN THE HYDRO – STATIC BEARING WITH NEAT SKETCHES?
(B) STATE AND PROVE THE PRESSURE EQUATION OF A JOURNAL BEARING?

QUE NO. – 8
(A) SKETCH VARIOUS TYPES OF BALL BEARINGS AND EXPLAIN THEIR FUNCTIONS?
(B) COMPARE SLIDING AND ROLLING CONTACT BEARINGS. STATE ANY FOUR ADVANTAGES AND THREE DISADVANTAGES OF ROLLING CONTACT BEARINGS?


PREVIOUS YEAR UNSOLVED QUESTION PAPERS – 3 (KURUKSHETRA UNIVERSITY)
TRIBOLOGY
QUE NO. – 1
(A) EXPLAIN TRIBOLOGICAL SYSTEMS AND THEIR CHARACTERISTIC FEATURES. EXPLAIN ONE SYSTEM IN DETAIL??
(B) STATE AND EXPLAIN ALL THE LAWS OF FRICTION AND EXPLAIN THE WORKING OF CROSS-CYLINDER ARRANGEMENT FOR MEASUREMENT OF FRICTION WITH SKETCHES?
QUE NO. – 2
(A) EXPLAIN DIFFERENT TECHNIQUES OF SURFACE EXAMINATION IN DETAIL?
(B) WHAT AREC THE CAUSES OF FRICTION? EXPLAIN ADHESION THEORY?
QUE NO. – 3
(A) DEFINE WEAR. EXPLAIN IN DETAIL ADHESIVE WEAR. HOW DO YOU MEASURE THE WEAR?
(B) EXPLAIN FREETING, CORROSION AND SURFACE FATIGUE WEAR?

QUE NO. – 4
(A) WHAT ARE THE QUANTITATIVE LAWS OF WEAR? DERIVE THE WEAR EQUATION?
(B) WHAT IS MECHANISM OF WEAR? WHICH TYPE OF WEAR FINDS APPLICATION IN INDUSTRY



QUE NO. – 5
(A) EXPLAIN ELASTO-HYDRODYNAMIC LUBRICATION?
(B) WITH THE HELP OF SKETCHES, EXPLAIN ROLLING CONTACT BEARINGS?
QUE NO. – 6
(A) EXPLAIN HYDRO-DYNAMIC LUBRICATION WITH THE HELP OF DIAGRAM?
(B) GIVE IMPORTANT PROPERTIES OF LUBRICANTS?
QUE NO. – 7
(A) WITH THE HELP OF NEAT SKETCHE EXPLAIN HYDROSTATIC BEARING?
(B) WHAT ARE THE IMPORTANT PROPERTIES OF BEARING MATERIALS? DISCUSS IN DETAIL?
QUE NO. – 8
(A) EXPLAIN THRUST BEARING WITH A SKETCH. WHAT ARE THE POROUS BEARINGS?
(B) EXPLAIN THE WORKING OF GAS BEARINGS WITH THE HELP OF DIAGRAMS?
Labels:

Comments

Post a Comment

Popular posts from this blog

APRON MECHANISM IN LATHE

APRON MECHANISM IN LATHE Apron Mechanism: Apron is attached to the carriage and hangs over the front side of the lathe bed. It is useful in providing power and hand feed to both carriage and cross-slide. It is also used to provide power feed to the carriage during thread cutting through two half nuts. The construction of apron is shown in Fig. Fig - Apron Mechanism Construction Power is transmitted from the spindle to the lead screw and feed rod through the spindle gear and tumbler gear arrangement. A worm is mounted on the feed rod by a sliding key. The worm meshes with a worm gear on whose axis another gear G1 is attached. Gear G1 is attached to a small gear G2 by a bracket as shown in the diagram. Gear G4 is positioned to be in mesh with the rack gear always. Another gear G3 is mounted on the same axis of gear G4. The carriage hand wheel meant for longitudinal feed is attached to the gear G5 on the same axis. The gears G3 and G5 are always in mesh. The gear G...
15 comments
Read more

DOM MANUAL / B-TECH / MECHANICAL / KUK - TO FIND THE SPEED AND TORQUE OF DIFFERENT GEARS IN AN EPICYCLIC GEAR TRAIN.

OBJECTIVE: TO FIND THE SPEED AND TORQUE OF DIFFERENT GEARS IN AN EPICYCLIC GEAR TRAIN. SPECIFICATIONS : 1.       GEAR TRAIN : SUN GEAR : 14 TEETH 2.       PLANT GEAR: 21 TEETH (2 NOS.) 3.       INTERNAL GEAR WITH : 56 TEETH TORQUE MEASUREMENT ·          INPUT TORQUE – MOTOR CURRENT CALIBRATED FOR MOTOR TORQUE. ·          PLANT CARRIER - PULLEY OF 50 MM DIA AND SPRING BALANCE. ·          INTERNAL GEAR - PULLEY, 120 MM DIA AND SPRING BALANCES. Ø   BOTH PULLEYS ARE PROVIDED WITH ROPE OF 12 Ø   MM DIA Ø   DRIVE MOTOR - 1HP DC MOTOR RPM MOTOR OPERATING ON 220 VOLTS Ø   50 HZ SUPLLY, DRIVING THE SUN GEAR. CURRENT(AMPS) TORQUE 1.00 0.5 1.20 1.5 1.40 2.5 ...
355 comments
Read more

Boiler Mounting - Water Level Indicator

WATER LEVEL INDICATOR Function:   It is indicates the water level inside the boiler to an observer. Working:  The water of the boiler comes into the glass tube through the lower tube and the steam through the upper tube. The water then stands in the glass tube at the same level as in the boiler. Two cocks are used to control the passage of between the boiler and the glass tube while the third cock is in used to discharge some of the water from inside the boiler to see whether the gauge is in proper order or not. The glass tube is protected by means of a cover, made of specially toughened glass, which will prevent any accident that may happen due to breaking of glass tube. It is used for ordinary boilers. Image - Water Level Indicator Figure - Water Level Indicator
2 comments
Read more