Skip to main content

IMPORTANT INTERVIEW QUESTIONS FOR FRESHERS / EXPERIENCED – MECHANICAL ENGINEERING (AUTOMOBILE ENGINEERING & GENERAL ENGINEERING)

IMPORTANT INTERVIEW QUESTIONS FOR FRESHERS / EXPERIENCED – MECHANICAL ENGINEERING (AUTOMOBILE ENGINEERING & GENERAL ENGINEERING)

Hi, this article is about some questions that might be helpful for you to clear an interview. These questions can be referred to by fresher as well as experienced Mechanical Automobile Engineers.
Answers to these questions will be shared soon in my next article.
  • WHAT IS SIX SIGMA
  • WHAT IS JIT (JUST IN TIME) TECHNIQUE
  • WHAT IS KAIZEN
  • WHAT IS PLANT LAYOUT
  • WHAT IS KANBAN
  • WHAT IS REDBIN ANALYSIS TECHNIQUE
  • WHAT IS PPAP (PRODUCTION PART APPROVAL PROCESS)
  • WHAT IS APQP (ADVANCE PRODUCT QUALITY PLANNING)
  • WHAT IS ORGANIZATION STRUCTURE
  • WHAT IS MSA (MEASUREMENT SYSTEM ANALYSIS)
  • WHAT IS SQC (STATISTICAL QUALITY CONTROL)
  • WHAT IS FMEA (FAILURE MODE EVALUATION AND ANALYSIS)
  • WHAT IS BATH TUB CURVE
  • WHAT IS SMED (SINGLE MINUTE EXCHANGE OF DIE SET)
  • WHAT IS VERNIER CALIPER, MICROMETER AND LEAST COUNT OF V.C. AND M.M
  • WHAT IS SINE GAUGE AND HOW IT WORKS
  • WHAT IS HEIGHT GAUGE AND HOW IT WORKS
  • WHAT IS V-BLOCK AND HOW IT WORKS
  • WHAT IS PPC (PRODUCTION PLANNING CONTROL)
  • WHAT IS TIME STUDY, MOTION STUDY
  • WHAT IS POKAYOKE
  • WHAT IS LEAN MANUFACTURING
  • WHAT IS 7 QC
  • WHAT IS 5S
  • WHAT IS TQM
  • WHAT IS MASTER SCHEDULING
  • WHAT IS ISO STANDARDS
  • WHAT IS ERP/SAP
  • WHAT IS OEE (OVERALL EQUIPMENT EFFICIENCY)
  • WHAT IS INVENTORY CONTROL
  • WHAT IS SWOT ANALYSIS
  • WHAT IS TPM (TOTAL PRODUCTIVE MAINTENANCE)
  • WHAT IS CONTROL CHARTS
  • WHAT IS FIFO
  • WHAT IS PDI
  • WHAT IS SHOP FLOOR
  • WHAT IS WORK STATION
  • WHAT IS PRODUCTION DATA SHEET
  • WHAT IS STRENGTH TESTING
  • WHAT IS TS-16949
  • WHAT IS DMAIC
  • WHAT IS WHY WHY TECHNIQUE
  • WHAT IS PROCESS CAPABILITY


Labels:

Comments

Post a Comment

Popular posts from this blog

DOM MANUAL / B-TECH / MECHANICAL / KUK - TO FIND THE SPEED AND TORQUE OF DIFFERENT GEARS IN AN EPICYCLIC GEAR TRAIN.

OBJECTIVE: TO FIND THE SPEED AND TORQUE OF DIFFERENT GEARS IN AN EPICYCLIC GEAR TRAIN. SPECIFICATIONS : 1.       GEAR TRAIN : SUN GEAR : 14 TEETH 2.       PLANT GEAR: 21 TEETH (2 NOS.) 3.       INTERNAL GEAR WITH : 56 TEETH TORQUE MEASUREMENT ·          INPUT TORQUE – MOTOR CURRENT CALIBRATED FOR MOTOR TORQUE. ·          PLANT CARRIER - PULLEY OF 50 MM DIA AND SPRING BALANCE. ·          INTERNAL GEAR - PULLEY, 120 MM DIA AND SPRING BALANCES. Ø   BOTH PULLEYS ARE PROVIDED WITH ROPE OF 12 Ø   MM DIA Ø   DRIVE MOTOR - 1HP DC MOTOR RPM MOTOR OPERATING ON 220 VOLTS Ø   50 HZ SUPLLY, DRIVING THE SUN GEAR. CURRENT(AMPS) TORQUE 1.00 0.5 1.20 1.5 1.40 2.5 ...
359 comments
Read more

MANUFACTURING PROCESS - DRAFT OR TAPER ALLOWANCE

DRAFT OR TAPER ALLOWANCE BY DRAFT IS MEANT THE TAPER PROVIDED BY THE PATTERN MAKER ON ALL VERTICAL SURFACES OF THE PATTERN SO THAT IT CAN BE REMOVED FROM THE SAND WITHOUT TEARING AWAY THE SIDES OF THE SAND MOLD AND WITHOUT EXCESSIVE RAPPING BY THE MOLDER. FIGURE  SHOWS A PATTERN HAVING NO DRAFT ALLOWANCE BEING REMOVED FROM THE PATTERN. IN THIS CASE, TILL THE PATTERN IS COMPLETELY LIFTED OUT, ITS SIDES WILL REMAIN IN CONTACT WITH THE WALLS OF THE MOLD, THUS TENDING TO BREAK IT.  FIGURE  IS AN ILLUSTRATION OF A PATTERN HAVING PROPER DRAFT ALLOWANCE. HERE, THE MOMENT THE PATTERN LIFTING COMMENCES, ALL OF ITS SURFACES ARE WELL AWAY FROM THE SAND SURFACE. THUS THE PATTERN CAN BE REMOVED WITHOUT DAMAGING THE MOLD CAVITY.  PATTERN HAVING DRAFT ON VERTICAL EDGES DRAFT ALLOWANCE VARIES WITH THE COMPLEXITY OF THE SAND JOB. BUT IN GENERAL INNER DETAILS OF THE PATTERN REQUIRE HIGHER DRAFT THAN OUTER SURFACES. THE AMOUNT OF DRAFT DEPENDS UPON THE LENGTH OF THE...
2 comments
Read more

ELECTROCHEMICAL MACHINING (ECM)

ELECTROCHEMICAL MACHINING (ECM) INTRODUCTION:- Electro chemical machining (ECM) is a method of removing metal by an electrochemical process. It is normally used for mass production and is used for working extremely hard materials or materials that are difficult to machine using conventional methods. Its use is limited to electrically conductive materials; however, this includes all metals. ECM can cut small or odd-shaped angles, intricate contours or cavities in extremely hard steel and exotic metals such as titanium, carbide etc. ECM is often characterized as "reverse electroplating," and is similar in concept to electrical discharge machining in that a high current is passed between an electrode and the part, through an electrolyte material removal process having a negatively charged electrode (cathode), a conductive fluid (electrolyte), and a conductive work piece (anode); however, in ECM there is no tool wear. The ECM cutting tool is guided along the desired ...
53 comments
Read more