IMPORTANT QUESTION OF RENEWAL ENERGY RESOURCES (MECHANICAL

IMPORTANT QUESTION OF RENEWAL ENERGY RESOURCES (MECHANICAL - 4TH YEAR)

IMPORTANT QUESTION OF RENEWAL ENERGY RESOURCES

(MECHANICAL - 4^TH YEAR)

UNIT - 1

QUE:-1) Drive an expression for Bernoulli’s equation in case of conservation of energy?

QUE:-2) What is Fick’s law of mass transfer? Explain the meaning of each term used in it and also discuss heat transfer by mass transfer?

UNIT – 2

QUE:-3) Discuss in detail about calculation of heat balance in case of solar water heater?

QUE:-4) Write a short on given topics-

a) Selective surfaces? b) Water Desalination?

c) Solar Pond? d)Solar Concentrator?

UNIT-3

QUE:-5) Discuss in detail about Impulse & Reaction turbine with diagram & Working principle?

QUE:-6) Write a short on given topics-

a) Pyrolysis? b)Alcoholic Fermentation?

UNIT – 4

QUE:-7) What is OTEC discuss with diagram and also write a short note on Method of

OTEC generation and also discuss about Open & Close cycle of OTEC?

QUE:-8) Discuss the basic principle used in Wind Energy Conversion System (WECS)? Throw some light on recent developments in this field?

Comments

APRON MECHANISM IN LATHE

APRON MECHANISM IN LATHE Apron Mechanism: Apron is attached to the carriage and hangs over the front side of the lathe bed. It is useful in providing power and hand feed to both carriage and cross-slide. It is also used to provide power feed to the carriage during thread cutting through two half nuts. The construction of apron is shown in Fig. Fig - Apron Mechanism Construction Power is transmitted from the spindle to the lead screw and feed rod through the spindle gear and tumbler gear arrangement. A worm is mounted on the feed rod by a sliding key. The worm meshes with a worm gear on whose axis another gear G1 is attached. Gear G1 is attached to a small gear G2 by a bracket as shown in the diagram. Gear G4 is positioned to be in mesh with the rack gear always. Another gear G3 is mounted on the same axis of gear G4. The carriage hand wheel meant for longitudinal feed is attached to the gear G5 on the same axis. The gears G3 and G5 are always in mesh. The gear G...

DOM MANUAL / B-TECH / MECHANICAL / KUK - TO FIND THE SPEED AND TORQUE OF DIFFERENT GEARS IN AN EPICYCLIC GEAR TRAIN.

OBJECTIVE: TO FIND THE SPEED AND TORQUE OF DIFFERENT GEARS IN AN EPICYCLIC GEAR TRAIN. SPECIFICATIONS : 1. GEAR TRAIN : SUN GEAR : 14 TEETH 2. PLANT GEAR: 21 TEETH (2 NOS.) 3. INTERNAL GEAR WITH : 56 TEETH TORQUE MEASUREMENT · INPUT TORQUE – MOTOR CURRENT CALIBRATED FOR MOTOR TORQUE. · PLANT CARRIER - PULLEY OF 50 MM DIA AND SPRING BALANCE. · INTERNAL GEAR - PULLEY, 120 MM DIA AND SPRING BALANCES. Ø BOTH PULLEYS ARE PROVIDED WITH ROPE OF 12 Ø MM DIA Ø DRIVE MOTOR - 1HP DC MOTOR RPM MOTOR OPERATING ON 220 VOLTS Ø 50 HZ SUPLLY, DRIVING THE SUN GEAR. CURRENT(AMPS) TORQUE 1.00 0.5 1.20 1.5 1.40 2.5 ...

Boiler Mounting - Water Level Indicator

WATER LEVEL INDICATOR Function: It is indicates the water level inside the boiler to an observer. Working: The water of the boiler comes into the glass tube through the lower tube and the steam through the upper tube. The water then stands in the glass tube at the same level as in the boiler. Two cocks are used to control the passage of between the boiler and the glass tube while the third cock is in used to discharge some of the water from inside the boiler to see whether the gauge is in proper order or not. The glass tube is protected by means of a cover, made of specially toughened glass, which will prevent any accident that may happen due to breaking of glass tube. It is used for ordinary boilers. Image - Water Level Indicator Figure - Water Level Indicator

Mechanical Guru's

Search This Blog