Skip to main content

TRIBOLOGY EXPECTED QUESTIONS

EXPECTED QUESTIONS (2010 – 2011)

UNIT – 1
1.       WHAT ARE DIFFERENT TRIBOLOGICAL SYSTEMS? EXPLAIN?
2.       WHAT IS SURFACE TOPOGRAPHY?
3.       WHAT ARE DIFFERENT DETERMINISTIC AND STOCHASTIC TRIBO MODELS FOR ASPERITY CONTACT?
4.       WHAT IS THE QUANTITATIVE LAW OF SLIDING & ROLLING FRICTION?
5.       WHAT IS THE ADHESION THEORY?

                                                             UNIT – 2

1.       DISCUSS THE DIFFERENT TYPES OF WEAR?
2.       WRITE SHORT NOTE ON FOLLOWING?
·         ABRASIVE WEAR
·         FREETING WEAR
·         EFFECT OF HARDNESS ON ABRASIVE WEAR RATE
·         INFLUENCE OF ABRASIVE PARTICLE SIZE ON ABRASIVE WEAR RATE
3.       EXPLAIN QUANTITATIVE LAWS OF ADHESIVE WEAR. DRIVE THE WEAR EQUATION AND HOW DO YOU MEASURE THE ADHESIVE WEAR?
4.       WHAT IS THE MECHANISM OF WEAR AND DISCUSS THE WEAR RESISTANT MATERIAL?
5.       WHAT ARE THE SOURCES OF WEAR? EXPLAIN STICK-SLIP ANDMOLECULAR ATTRACTION THEORY WITH NEAT DIAGRAM?
UNIT – 3
1.       WHAT ARE LUBRICANTS & DISCUSS THE TYPES OF LUBRICATION WITH NEAT SKETCH?
2.       WRITE ABOUT FUNCTIONS OF LUBRICATIONS, THEIR TYPES AND PROPERTIES?
3.       DISCUSS WITH THE HELP OF SKETCHES, EXPLAIN ROLLING CONTACT BEARINGS?
4.       WHAT IS LUBRICANT ADDITIVES?
UNIT – 4
1.       WHAT ARE ANTIFRICTION BEARINGS? DISCUSS THEIR ADVANTAGES & LIMITATIONS?
2.       DERIVE AN EQUATION FOR LOAD CARRIED IN FOOTSTEP BEARINGS?
3.       EXPLAIN IN DETAIL THE CIRCULAR STEP THRUST BEARING AND WRITE DOWN THE PRESSURE DISTRIBUTION EQUATION?
4.       STATE AND PROVE THE PRESSURE EQUATION OF A SHOIT BEARING? WHAT IS THE DIFFERENT BEARING MATERIAL USED? EXPLAIN?
5.       EXPLAIN THE WORKING OF GAS BEARINGS AND POROUS BEARING WITH THE HELP OF DIAGRAM?

Comments

  1. Unknown29 May 2014 at 16:20

    DETERMINISTIC AND STOCHASTIC TRIBO MODELS FOR ASPERITY CONTACT
    sir can u please suggest what to write in this question

    ReplyDelete

Post a Comment

Popular posts from this blog

DOM MANUAL / B-TECH / MECHANICAL / KUK - TO FIND THE SPEED AND TORQUE OF DIFFERENT GEARS IN AN EPICYCLIC GEAR TRAIN.

OBJECTIVE: TO FIND THE SPEED AND TORQUE OF DIFFERENT GEARS IN AN EPICYCLIC GEAR TRAIN. SPECIFICATIONS : 1.       GEAR TRAIN : SUN GEAR : 14 TEETH 2.       PLANT GEAR: 21 TEETH (2 NOS.) 3.       INTERNAL GEAR WITH : 56 TEETH TORQUE MEASUREMENT ·          INPUT TORQUE – MOTOR CURRENT CALIBRATED FOR MOTOR TORQUE. ·          PLANT CARRIER - PULLEY OF 50 MM DIA AND SPRING BALANCE. ·          INTERNAL GEAR - PULLEY, 120 MM DIA AND SPRING BALANCES. Ø   BOTH PULLEYS ARE PROVIDED WITH ROPE OF 12 Ø   MM DIA Ø   DRIVE MOTOR - 1HP DC MOTOR RPM MOTOR OPERATING ON 220 VOLTS Ø   50 HZ SUPLLY, DRIVING THE SUN GEAR. CURRENT(AMPS) TORQUE 1.00 0.5 1.20 1.5 1.40 2.5 ...
359 comments
Read more

MANUFACTURING PROCESS - DRAFT OR TAPER ALLOWANCE

DRAFT OR TAPER ALLOWANCE BY DRAFT IS MEANT THE TAPER PROVIDED BY THE PATTERN MAKER ON ALL VERTICAL SURFACES OF THE PATTERN SO THAT IT CAN BE REMOVED FROM THE SAND WITHOUT TEARING AWAY THE SIDES OF THE SAND MOLD AND WITHOUT EXCESSIVE RAPPING BY THE MOLDER. FIGURE  SHOWS A PATTERN HAVING NO DRAFT ALLOWANCE BEING REMOVED FROM THE PATTERN. IN THIS CASE, TILL THE PATTERN IS COMPLETELY LIFTED OUT, ITS SIDES WILL REMAIN IN CONTACT WITH THE WALLS OF THE MOLD, THUS TENDING TO BREAK IT.  FIGURE  IS AN ILLUSTRATION OF A PATTERN HAVING PROPER DRAFT ALLOWANCE. HERE, THE MOMENT THE PATTERN LIFTING COMMENCES, ALL OF ITS SURFACES ARE WELL AWAY FROM THE SAND SURFACE. THUS THE PATTERN CAN BE REMOVED WITHOUT DAMAGING THE MOLD CAVITY.  PATTERN HAVING DRAFT ON VERTICAL EDGES DRAFT ALLOWANCE VARIES WITH THE COMPLEXITY OF THE SAND JOB. BUT IN GENERAL INNER DETAILS OF THE PATTERN REQUIRE HIGHER DRAFT THAN OUTER SURFACES. THE AMOUNT OF DRAFT DEPENDS UPON THE LENGTH OF THE...
2 comments
Read more

Boiler Mounting - Water Level Indicator

WATER LEVEL INDICATOR Function:   It is indicates the water level inside the boiler to an observer. Working:  The water of the boiler comes into the glass tube through the lower tube and the steam through the upper tube. The water then stands in the glass tube at the same level as in the boiler. Two cocks are used to control the passage of between the boiler and the glass tube while the third cock is in used to discharge some of the water from inside the boiler to see whether the gauge is in proper order or not. The glass tube is protected by means of a cover, made of specially toughened glass, which will prevent any accident that may happen due to breaking of glass tube. It is used for ordinary boilers. Image - Water Level Indicator Figure - Water Level Indicator
6 comments
Read more