Skip to main content

MECHANICAL PROJECT LIST


MECHANICAL ENGINEERING PROJECT LIST

1.      ROBOTIC TROLLEY FOR MATERIAL HANDLING
2.  AUTOMATIC DUAL BELT MATERIAL HANDLING SYSTEM WITH OVERLOAD SENSING SYSTEM
3.      ROBOTIC ARM WITH GRIPPER
4.      AUTOMATIC GRINDING MACHINE
5.      PNEUMATIC/HYDRAULIC ROBOTIC ARM
6.      PNEUMATIC/HYDRAULIC CRANE
7.      PNEUMATIC JACK
8.      STEPPER MOTOR CONTROL WITH SELECTED STEPS FOR CONVEYOR BELT
9.      OBJECT REJECTION & COUNTING MACHINE
10.  HYDRAULIC JACK
11.  ANTI LOCK SENSOTRONIC BRAKING SYSTEM
12.  ROBOTIC CRANE
13.  ROBOTIC TROLLEY FOR MATERIAL HANDLING
14.  ELECTROMAGNETIC BRAKEING SYSTEM USING INDUCTION COIL
15.  BREAD SLICER AUTOMATIC
16.  AUTOMATIC LATHE MACHINE CONTROL
17.  AUTOMATIC STAMPING MACHINE FOR LETTER (MINI PRINTING MACHINE)
18.  MULTI-LEVEL PARKING SYSTEM
19.  ELECTROMAGNETIC CLUTCH
20.  WIND MILL
21.  SOLAR SUN SEEKER
22.  THERMAL POWER PLANT USING STEAM
23.  HYDEL POWER DAM
24.  ELECTRICAL ENERGY FROM SPEED BREAKER
25.  ELECTRICAL ENERGY FROM BUSY ROADS
26.  PADDLE CONTROLLED MOBILE CHARGER CUM EMERGENCY LIGHT
27.  HYBRID CHIMNEY
28.  SOLAR POWERED REFRIGERATOR
29.  ELECTRICAL ENERGY FROM COMPRESSED AIR
30.  WIND BELT
31.  REGENERATIVE CRANE
32.  PNEUMATIC TRANSPORT SYSTEM
33.  AUTOMATIC MILLING MACHINE
34.  ANTI LOCK BREAKING CAR
35.  GAS TURBINE GENERATOR
36.  SEAT BELT AUTOMATIC
37.  ELECTROMECHANICAL SHOCK ABSORBER
38.  ROBOTIC CAR WITH SENSORS
39.  LINE TRACER INDUSTRIAL VEHICLE
40.  AMPHIBIAN ROBOTIC CAR
41.  REGENERATIVE BRAKING SYSTEM
42.  IR AUTO BRAKING
43.  ROBOTIC RADAR SYSTEM
44.  HYDRAULIC BRAKES
45.  ROBOTIC LIFT/ ESCALATOR
46.  COMPRESSOR LESS THERMO-EMF REFRIGERATOR
47.  MOVING ESCALATORS
48.  OVER DRIVE GEAR SYSTEM
49.  MAGNETIC ABRASIVE MACHINING
50.  DEEP FREEZER cum COLD STORAGE USING COMPRESSOR –REFRIGERATION
51.  HEAT EXCHANGER-PIPES
52.  HYBRID MOTORBIKE
53.  MOTORIZED ELECTRIC AIR COMPRESSOR
54.  ENGINE BASED AIR COMPRESSOR
55.  ACTUAL CAR LIFTING JACK: A MOTORIZED JACK
56.  MOVING BRIDGE
57.  COMPRESSED AIR ENGINE CAR
58.  HYDRAULIC /COMPRESSED AIR BASED LIFTING JACK
59.  DRIVER LESS CAR
60.  AUTOMATIC LANDING GEAR MECHANISM IN AIRCRAFT
61.  COAL CRUSHER MACHINE
62.  SOLAR WATER HEATER - MAGNIFIER LENS BASED
63.  UNMANNED RAILWAY CROSSING
64.  TORQUE TESTING DEVICE
65.  ELECTRIC HYBRID BICYCLE
66.  STEERING CONTROLLED HEADLIGHT
67.  MOTORIZED WHEEL CHAIR
68.  MAGNETIC LEVITATION PLATFORM
69.  ELECTROMACHANICAL BRAKE
70.  STERLING ENGINE



Labels:

Comments

Post a Comment

Popular posts from this blog

DOM MANUAL / B-TECH / MECHANICAL / KUK - TO FIND THE SPEED AND TORQUE OF DIFFERENT GEARS IN AN EPICYCLIC GEAR TRAIN.

OBJECTIVE: TO FIND THE SPEED AND TORQUE OF DIFFERENT GEARS IN AN EPICYCLIC GEAR TRAIN. SPECIFICATIONS : 1.       GEAR TRAIN : SUN GEAR : 14 TEETH 2.       PLANT GEAR: 21 TEETH (2 NOS.) 3.       INTERNAL GEAR WITH : 56 TEETH TORQUE MEASUREMENT ·          INPUT TORQUE – MOTOR CURRENT CALIBRATED FOR MOTOR TORQUE. ·          PLANT CARRIER - PULLEY OF 50 MM DIA AND SPRING BALANCE. ·          INTERNAL GEAR - PULLEY, 120 MM DIA AND SPRING BALANCES. Ø   BOTH PULLEYS ARE PROVIDED WITH ROPE OF 12 Ø   MM DIA Ø   DRIVE MOTOR - 1HP DC MOTOR RPM MOTOR OPERATING ON 220 VOLTS Ø   50 HZ SUPLLY, DRIVING THE SUN GEAR. CURRENT(AMPS) TORQUE 1.00 0.5 1.20 1.5 1.40 2.5 ...
359 comments
Read more

MANUFACTURING PROCESS - DRAFT OR TAPER ALLOWANCE

DRAFT OR TAPER ALLOWANCE BY DRAFT IS MEANT THE TAPER PROVIDED BY THE PATTERN MAKER ON ALL VERTICAL SURFACES OF THE PATTERN SO THAT IT CAN BE REMOVED FROM THE SAND WITHOUT TEARING AWAY THE SIDES OF THE SAND MOLD AND WITHOUT EXCESSIVE RAPPING BY THE MOLDER. FIGURE  SHOWS A PATTERN HAVING NO DRAFT ALLOWANCE BEING REMOVED FROM THE PATTERN. IN THIS CASE, TILL THE PATTERN IS COMPLETELY LIFTED OUT, ITS SIDES WILL REMAIN IN CONTACT WITH THE WALLS OF THE MOLD, THUS TENDING TO BREAK IT.  FIGURE  IS AN ILLUSTRATION OF A PATTERN HAVING PROPER DRAFT ALLOWANCE. HERE, THE MOMENT THE PATTERN LIFTING COMMENCES, ALL OF ITS SURFACES ARE WELL AWAY FROM THE SAND SURFACE. THUS THE PATTERN CAN BE REMOVED WITHOUT DAMAGING THE MOLD CAVITY.  PATTERN HAVING DRAFT ON VERTICAL EDGES DRAFT ALLOWANCE VARIES WITH THE COMPLEXITY OF THE SAND JOB. BUT IN GENERAL INNER DETAILS OF THE PATTERN REQUIRE HIGHER DRAFT THAN OUTER SURFACES. THE AMOUNT OF DRAFT DEPENDS UPON THE LENGTH OF THE...
2 comments
Read more

ELECTROCHEMICAL MACHINING (ECM)

ELECTROCHEMICAL MACHINING (ECM) INTRODUCTION:- Electro chemical machining (ECM) is a method of removing metal by an electrochemical process. It is normally used for mass production and is used for working extremely hard materials or materials that are difficult to machine using conventional methods. Its use is limited to electrically conductive materials; however, this includes all metals. ECM can cut small or odd-shaped angles, intricate contours or cavities in extremely hard steel and exotic metals such as titanium, carbide etc. ECM is often characterized as "reverse electroplating," and is similar in concept to electrical discharge machining in that a high current is passed between an electrode and the part, through an electrolyte material removal process having a negatively charged electrode (cathode), a conductive fluid (electrolyte), and a conductive work piece (anode); however, in ECM there is no tool wear. The ECM cutting tool is guided along the desired ...
53 comments
Read more