Skip to main content

Terms and Conditions

Below are the Terms and Conditions for use of www.mechanicalhero.com. Please read these carefully. If you need to contact us regarding any aspect of the following terms of use of our website, please contact us on the following email address - sumitshrivastva4you@gmail.com. 

By accessing the content of www.mechanicalhero.com (hereafter referred to as website) you agree to the terms and conditions set out herein and also accept our Privacy Policy. If you do not agree to any of the terms and conditions you should not continue to use the Website and leave immediately. 

You agree that you shall not use the website for any illegal purposes, and that you will respect all applicable laws and regulations. 

You agree not to use the website in a way that may impair the performance, corrupt or manipulate the content or information available on the website or reduce the overall functionality of the website. 

You agree not to compromise the security of the website or attempt to gain access to secured areas of the website or attempt to access any sensitive information you may believe exist on the website or server where it is hosted. 

You agree to be fully responsible for any claim, expense, losses, liability, and costs including legal fees incurred by us arising from any infringement of the terms and conditions in this agreement and to which you will have agreed if you continue to use the website. 

The reproduction, distribution in any method whether online or offline is strictly prohibited. The work on the website and the images, logos, text and other such information is the property of www.mechanicalhero.com (unless otherwise stated). 

Disclaimer 
Though we strive to be completely accurate in the information that is presented on our site, and attempt to keep it as up to date as possible, in some cases, some of the information you find on the website may be slightly outdated. 

www.mechanicalhero.com reserves the right to make any modifications or corrections to the information you find on the website at any time without notice. 

Change to the Terms and Conditions of Use
We reserve the right to make changes and to revise the above mentioned Terms and Conditions of use. 

Popular posts from this blog

APRON MECHANISM IN LATHE

APRON MECHANISM IN LATHE Apron Mechanism: Apron is attached to the carriage and hangs over the front side of the lathe bed. It is useful in providing power and hand feed to both carriage and cross-slide. It is also used to provide power feed to the carriage during thread cutting through two half nuts. The construction of apron is shown in Fig. Fig - Apron Mechanism Construction Power is transmitted from the spindle to the lead screw and feed rod through the spindle gear and tumbler gear arrangement. A worm is mounted on the feed rod by a sliding key. The worm meshes with a worm gear on whose axis another gear G1 is attached. Gear G1 is attached to a small gear G2 by a bracket as shown in the diagram. Gear G4 is positioned to be in mesh with the rack gear always. Another gear G3 is mounted on the same axis of gear G4. The carriage hand wheel meant for longitudinal feed is attached to the gear G5 on the same axis. The gears G3 and G5 are always in mesh. The gear G
14 comments
Read more

Boiler Mountings - Dead Weight Safety Valve

DEAD WEIGHT SAFETY VALVE Function:- A valve is placed upon a valve seat that is fixed upon a long vertical pipe having a flange at the bottom for fixing at the top of the boiler. Suspended at the top of the valve is the weight carrier that carries cast iron rings. The total weight must be sufficient to keep the valve on its seat against the normal working pressure. When the steam pressure exceeds the normal limit, it lifts the valve with its weight & the excess steam escape through the pipe to the outside. This valve is used only with stationary type of boilers. It is the most elementary type of safety valve. The objection to dead weight safety valve is the heavy weight that has to be carried. Image - Dead Weight Safety Valve Figure - Dead Weight Safety Valve
10 comments
Read more

DOM MANUAL / B-TECH / MECHANICAL / KUK - TO FIND THE SPEED AND TORQUE OF DIFFERENT GEARS IN AN EPICYCLIC GEAR TRAIN.

OBJECTIVE: TO FIND THE SPEED AND TORQUE OF DIFFERENT GEARS IN AN EPICYCLIC GEAR TRAIN. SPECIFICATIONS : 1.       GEAR TRAIN : SUN GEAR : 14 TEETH 2.       PLANT GEAR: 21 TEETH (2 NOS.) 3.       INTERNAL GEAR WITH : 56 TEETH TORQUE MEASUREMENT ·          INPUT TORQUE – MOTOR CURRENT CALIBRATED FOR MOTOR TORQUE. ·          PLANT CARRIER - PULLEY OF 50 MM DIA AND SPRING BALANCE. ·          INTERNAL GEAR - PULLEY, 120 MM DIA AND SPRING BALANCES. Ø   BOTH PULLEYS ARE PROVIDED WITH ROPE OF 12 Ø   MM DIA Ø   DRIVE MOTOR - 1HP DC MOTOR RPM MOTOR OPERATING ON 220 VOLTS Ø   50 HZ SUPLLY, DRIVING THE SUN GEAR. CURRENT(AMPS) TORQUE 1.00 0.5 1.20 1.5 1.40 2.5 1.60 3.0 1.80 4.0 2.00 5.0 2.20 6.0 MOTOR  CALIBRATION  CHART THEORY : WHENEVER THE DISTANCE BETWEEN THE DRIVING AND DRIVEN MEMBER, (BOTH SHAFTS ARE NOT OPERATING ON THE SAME A
351 comments
Read more